Wire Size Rangę (<) | Torqu- | |||||
Nnme | Description | Maximum | Minimum | M,iximum | Recommended | |
1 | Aralog 1/0 | Aratog 10 Signals | 2.5 mmz (14 AWG) | 0.5 mm* (22 AWG) | 0.2 N-m 1.8 IbHn. | 0.2 N«m 18lt*in |
2 | Digital Irpuls | Digital Input Signals | 2.5 mm* (14 AWG) | 0.5 mm* (22 WG) | 0.2 N-m 1.8lb.-in. | 0.2 N«m 1.81 Mn |
3 | Digital Ouiputs | Digilal Oul Relays | 2.5 mm* (14 AWG) | 0.5 mm* (22 AWG) | 0.5 N-m 4.5lb.-in. | 0.5 Nnti 4.S It-in |
No. | Signal | Description | |
1 | Analog In 1 (-) 0) | Isolated (9, bipolar, ditferential, 9 bit & sign, 88k ohm input impedance. A jumper fpage 28) selects: 0-10V. ±10V, 4-20mA. Default: 0-10V (Ri =200k), 4-20mA (Ri=100 ohm). | |
2 | Analog In 1 (+) W | ||
3 | Analog In 2 (-) (U | ||
4 | Analog In 2 (+) (D | ||
5 | -10VPotReference | - | 2k ohm minimum, 10 mA maximum load, 1% accuracy. |
6 | Pot Common (GND) | For (+) and (-) 10V pot references. | |
7 | +10V Pot Reference | - | 2kohm minimum, 10mA maximumload, 1%aocuracy. |
8 | Analog Out 1 (+) | (4) | Bipolar (current out is not bipolar), 9 bit & sign, 2kohm minimum load. A jumper (seepage_22) selects: 0-10V, ±10V, 4-20mA. |
9 | Analog Out Common | ||
10 | Analog Out 2 (+) | ||
11 | Digital In 1 | Stop - CF | 115V AC. 50/60 Hz - Opto isolated Low State: lessthan 30V AC High State: greaterthan 40V AC 24V DC - Opto isolated (250V) Low State: lessthan 5V DC High State: greater than 20V DC 11.2 mA DC Enable: Digital Input 6 is jumper selectable for HW Enable. On-Time: < 16.7ms, Off-Time < 1 ms |
12 | Digital In 2 | Start | |
13 | Digital In 3 | Auto/Man | |
14 | Digital In 4 | Speed Sel 1 | |
15 | Digital In 5 | Speed Sel 2 | |
16 | Digital In 6/Hardware Enable, seepg. 22 | Speed Sel 3 | |
17 18 | Digital In Common | Allows source orsink operation. Terminals 17/18 & 19 can also be used to provide backup power to DPI and control devices. | |
19 | +24VDC(2) | - | Drive supplied logie input power. |
20 | 24V Common (2) | - | Common for internal power supply. |
21 | Digital Out 1 - N.C. P) | Fault | Max. Resistive Load: 240V AC/30V DC -1200VA, 150W Max. Current: 5A, Min. Load: 10mA |
22 | Digital Out 1 Common | ||
23 | Digital Out 1 - N.O.0) | NOTFault | |
24 | Digital Out 2-N.C. P) | NOT Run | Max. Inductwe Load: 240V AC/30V DC - 840VA, 105W Max. Current: 3.5A. Min. Load: 10mA |
25 | Digital Out 2/3 Com. | ||
26 | Digital Out3-N.0.0) | Run |