| Selection features | ICU24 | ICU24F | IPM25, FS A Frame size A | IPM25, FS B Frame size B | |
| • Integrated safety functions acc. to EN 954-1 (Category 3) or IEC 61508 (SIL 2) | - | •Safe Torque Off (STO) • Safe Stop 1 (SS1) (sensorless) • Safely Limited Speed (SLS) (sensorless) | - | - | |
| •Power | - | - | 0.75 kW/ 1.0 hp | 2.2 kW/ 4.0 kW/ 3.0 hp 5.0 hp | |
| • Rated input current (at 50 °C ambient temperature) | - | - | 1.9 A | 5.7 A 9.6 A | |
| • Rated output current (at 50 °C ambient temperature) | - | - | 2.1 A | 5.9 A 10.2 A | |
| • Installation dimensions (W x H x D) in mm (including terminal module) | 15 x 220 x 156 | - | 65 x 290 x 156 | 130 x 290 x 156 | |
| Line voltage | 3 AC 380 V to 480 V +10 % / -10 % | ||||
| Power frequency | 47 Hz to 63 Hz | ||||
| Overload capability | • Overload current 1.5 x rated output current (i.e. 150 % overload) for 60 s, cycle time 300 s • Overload current 2 x rated output current (i.e. 200 % overload) for 3 s, cycle time 300 s | ||||
| Output frequency | 0 Hz to 650 Hz | ||||
| Pulse frequency | 8 kHz (standard), 2 kHz to 16 kHz (in 2 kHz steps) | ||||
| Skippable frequency range | 1, parameterizable | ||||
| Converter efficiency | > 96 % at rated load of the motor | ||||
| Interfaces | • PROFIBUS or PROFINET interface via the ET 200S backplane bus • RS232 interface with USS protocol for startup on a PC with the STARTER system start-up software • Slot for one optional memory card (MMC) for uploading and downloading parameter settings • PTC/KTY84 interface for monitoring the motor temperature • Speed encoder interface (sub D connector) for unipolar HTL incremental encoder | ||||
| Control methods | • V/f contro — linear (M~n) with/without flux current control (FCC), quadratic (M~n2)or parameterizable • Vector control — with sensor/sensorless •Torque control | ||||
| Operating functions | Inching mode, free function blocks (FFB), positioning deceleration ramp, automatic restart after stoppage due to power failure, bumpless connection of the converter to the rotating motor | ||||
| Braking functions | • Regenerating braking without brake chopper or pulse resistor • Optional brake control module for electromechanical holding brake | ||||
| Protection functions | Undervoltage, overvoltage, ground fault, short-circuit, stall prevention, thermal motor protection (?t or sensor), converter overtemperature, locked-rotor protection | ||||
| Connectable motors | Low-voltage asynchronous motors (max. motor cable length: 50 m (shielded), 100 m (unshielded)) | ||||
| Degree of protection | IP20 | ||||
| Operating temperature | • Vertical station configuration: -10 °C to +40 °C (+14 °F to +104 °F) • Horizontal station configuration: -10 °C to +50 °C (+14 °F to +122 °F) (max. +60 °C (+140 °F) with derating) | ||||
| Conformity with standards | UL, cUL, CE, c-tick, Low-Voltage Directive 73/23/EEC, EMC Directive 89/336/EEC | ||||
| • External EMC filter for compliance with EMC Class A (acc. to EN 55011) • Memory card (MMC) for storing frequency converter parameters • Paper documentation (operating manual, list manual etc.) plus documentation on CD-ROM | |||||