Falowniki wortal - Siemens - Simatic ET 200S FC Dane znamionowe

falowniki Omron

Falowniki wortal systemów napędowych
Znajdziesz tu dane znamionowe, opisy schematy i instrukcje falowników .

Falowniki Siemens

Falowniki

Szukaj

Ostatnie artykuły o falownikach

Forum falowników

www.falowniki.info

Siemens - Simatic ET 200C FC

Selection features	ICU24	^ICU24F	IPM25, FS A Frame size A	IPM25, FS B Frame size B
• Integrated safety functions acc. to EN 954-1 (Category 3) or IEC 61508 (SIL 2)	-	•Safe Torque Off (STO) • Safe Stop 1 (SS1) (sensorless) • Safely Limited Speed (SLS) (sensorless)	-	-
•Power	-	^-	0.75 kW/ 1.0 hp	2.2 kW/ 4.0 kW/ 3.0 hp 5.0 hp
• Rated input current (at 50 °C ambient temperature)	-	^-	1.9 A	5.7 A 9.6 A
• Rated output current (at 50 °C ambient temperature)	-	^-	2.1 A	5.9 A 10.2 A
• Installation dimensions (W x H x D) in mm (including terminal module)	15 x 220 x 156	^-	65 x 290 x 156	130 x 290 x 156

Line voltage	3 AC 380 V to 480 V +10 % / -10 %
Power frequency	47 Hz to 63 Hz
Overload capability	• Overload current 1.5 x rated output current (i.e. 150 % overload) for 60 s, cycle time 300 s • Overload current 2 x rated output current (i.e. 200 % overload) for 3 s, cycle time 300 s
Output frequency	0 Hz to 650 Hz
Pulse frequency	8 kHz (standard), 2 kHz to 16 kHz (in 2 kHz steps)
Skippable frequency range	1, parameterizable
Converter efficiency	> 96 % at rated load of the motor
Interfaces	• PROFIBUS or PROFINET interface via the ET 200S backplane bus • RS232 interface with USS protocol for startup on a PC with the STARTER system start-up software • Slot for one optional memory card (MMC) for uploading and downloading parameter settings • PTC/KTY84 interface for monitoring the motor temperature • Speed encoder interface (sub D connector) for unipolar HTL incremental encoder

Control methods	• V/f contro — linear (M~n) with/without flux current control (FCC), quadratic (M~n²)or parameterizable • Vector control — with sensor/sensorless •Torque control
Operating functions	Inching mode, free function blocks (FFB), positioning deceleration ramp, automatic restart after stoppage due to power failure, bumpless connection of the converter to the rotating motor
Braking functions	• Regenerating braking without brake chopper or pulse resistor • Optional brake control module for electromechanical holding brake
Protection functions	Undervoltage, overvoltage, ground fault, short-circuit, stall prevention, thermal motor protection (?t or sensor), converter overtemperature, locked-rotor protection
Connectable motors	Low-voltage asynchronous motors (max. motor cable length: 50 m (shielded), 100 m (unshielded))

Degree of protection	IP20
Operating temperature	• Vertical station configuration: -10 °C to +40 °C (+14 °F to +104 °F) • Horizontal station configuration: -10 °C to +50 °C (+14 °F to +122 °F) (max. +60 °C (+140 °F) with derating)

Conformity with standards	UL, cUL, CE, c-tick, Low-Voltage Directive 73/23/EEC, EMC Directive 89/336/EEC

	• External EMC filter for compliance with EMC Class A (acc. to EN 55011) • Memory card (MMC) for storing frequency converter parameters • Paper documentation (operating manual, list manual etc.) plus documentation on CD-ROM

WebSystem tel. 048 383.01.44 | wortal-> www.falowniki.pl | forum-> www.falowniki.info | porównaj-> www.falowniki.com.pl

Warto zobaczyć

Giełda falowników

Falownik Lenze 9300 Vector 110kW

Falownik Lenze 9300 Vector 110kW EVF9335-EVV030

Więcej…

dobór falowniki Wortal napędów energoelektronicznych www.falowniki.pi . Napędy energoelektroniczne do regulacji prędkości obrotowej silników elektrycznych.

Falowniki Siemens

Falowniki

Szukaj

Ostatnie artykuły o falownikach

Siemens - Simatic ET 200C FC

Dane znamionowe falownika Siemens Simatic ET 200S FC

Warto zobaczyć

Giełda falowników

Falownik Lenze 9300 Vector 110kW

Softstart eTran 7,5kW SET200-7.5

Softstart eTran 11kW SET500-11

Siemens Simovert 45kVA 6SE-1245-2AA00

Siemens Simovert 22kVA 6SE-1222-2AA02

Siemens Simovert 22kVA 6SE-1222-2AA03